SmartConfig2.1

⌘K
  2. Home
  4. Docs
  6. SmartConfig2.1
  8. 5.1 User defined
  10. 5.1.14 Function Reference

5.1.14 Function Reference

F1 End Program

Ends program if this function gets called
ParameterDescription
noneEnds program execution

Example:
F1

F2 Jump to Line

Continoue code in defined line
ParameterRangeDescription
S1–max linesLine number
P1–255Optional sub-program

Example:
F2,S1

F3 Delay

Waits for defined time
ParameterRangeDescription
T0–65535Time in seconds
P1–255Optional sub-program

Example:
F3,T10

F4 Wait for Next Alarm

Uses the internal clock and wait for next set alarm time
ParameterRangeDescription
P1–255Optional sub-program

F5 Switch Module

Switch the power the module channel
ParameterRangeDescription
T0–65535Duration
S0–10=OFF, 1=ON
P1–255Optional sub-program

F6 Switch Sensor

Switch the power to all active sensor channels
ParameterRangeDescription
T0–65535Duration
S0–10=OFF, 1=ON
P1–255Optional sub-program

F7 Switch Output

Switch defined output
ParameterRangeDescription
T0–65535Duration
S0–10=OFF, 1=ON
O1–4Output number
P1–255Optional sub-program

Example:
F7,T5,S1,O2

F8 Read Sensor

Reads frequently from the active sensor channels
ParameterRangeDescription
T0–65535Read duration
S1Optional
0 = read and save
1 = read and discard
P1–255Optional sub-program

F9 Send Data via Telemetry

send the sensor string via telemetry with a prefix to seperate data
ParameterRangeDescription
Snumerical indexVariable prefix
P1–255Optional sub-program

F10 Send Custom Telemetry value

comming soon
ParameterRangeDescription
P1–255Optional sub-program

F11 Send Clean Command

Sends clean command to connected sensors
ParameterRangeDescription
T0–65535Duration
P1–255Optional sub-program

F12 Set Sub-Program

Sets the sub program
ParameterRangeDescription
I1–254Sub-program to activate

Example:
F12,I1

F13 End Sub-Program

Ends sub program
ParameterRangeDescription
T0–2Exit mode
S1–max linesTarget line (T=2)
P1–255Sub-program label

Exit modes:

TMeaning
0Return to caller
1Continue
2Jump to line S

F14 Formula

Use basic formulas to evaluate or manipulate
ParameterRangeDescription
P1–255Optional sub-program

Supported variables: a b c d A B C D E G X Y Z r

Example:
F14,a*G

F15 Temporary Storage

Access temporary storage and set values
ParameterRangeDescription
T0–3Mode
S1–3Storage U/V/W/X/Y/Z
O0–65535Value
P1–255Optional sub-program

Modes:

TOperationSymbol
0Reset0
1Increment+1
2Decrement-1
3Set value=O or =r

F16 Compare Value

Compares two values, if comparison is true it sets a sub-program
ParameterRangeDescription
T0–5Compare mode
S0–65535Reference value
O0–65535Value to compare
I1–254Sub-program to activate
P1–254Optional sub-program

Compare modes:

TMeaningOperator
0Equal to==
1Greater than>
2Less than<
3Not equal!=
4Greater or equal>=
5Less or equal<=

F17 Pulse Counter Set

Access pulse counter, reset or set to value
ParameterRangeDescription
T0–3Mode
S1–8Pulse counter
O0–65535Value
P1–254Optional sub-program

Modes:

TOperationSymbol
0Reset0
1Increment+1
2Decrement-1
3Set value=O

F18 Pulse Counter Compare

Waits for Pulse counter to reach or till timeout, sets sub program either way
ParameterRangeDescription
T0–65535Timeout
O1–8Pulse counter
S0–65535Target value
I1–254Sub-program
P1–255Optional sub-program

Behavior:
If counter reaches target or timeout expires, sub-program I is activated.Execution always continues.

F50 AquaMate

Sends command to AquaMate
ParameterRangeDescription
S1–16Sub-address
O1–13Position
I0–10=OFF, 1=ON

F51 AutoSampler

Sends command to AutoSampler

Parameter Overview

LetterNameDescription
TTaskDefines which operation is executed
SSub-addressAddress of the AutoSampler8 module
OPositionValve position or internal output
IStateON/OFF state (task-dependent)
PSub-programOptional sub-program label

Parameter Ranges

ParameterAllowed RangeNotes
T0–4Task selector
S1–16Module sub-address
O1–8Valve position (task-dependent)
I0–10=OFF, 1=ON
P1–254Optional

Runtime placeholders are allowed in all parameters but bypass static checks.

Task Selection (T)

TTask NameDescription
0Switch 8-port valveControls the 8-position rotary valve
1Switch 2-port valveControls the 2-position valve
2Switch peristaltic pumpTurns peristaltic pump ON or OFF
3Switch diaphragm pumpTurns diaphragm pump ON or OFF
4Read pressureRequests pressure data from module

Task-Specific Parameter Behavior

T = 0 Switch 8-port valve

Controls the main 8-port rotary valve.

ParameterMeaning
SModule sub-address
OValve position (1–8)
IState (0=OFF, 1=ON)

T = 1 Switch 2-port valve

Controls the 2-port valve.

ParameterMeaning
SModule sub-address
OValve position (1–2)
IState (0=OFF, 1=ON)

T = 2 Switch peristaltic pump

Controls the peristaltic pump motor.

ParameterMeaning
SModule sub-address
IState (0=OFF, 1=ON)

T = 3 Switch diaphragm pump

Controls the diaphragm pump.

ParameterMeaning
SModule sub-address
IState (0=OFF, 1=ON)

T = 4 Read pressure

Requests pressure data from the AutoSampler8 module.

ParameterMeaning
SModule sub-address
OInternal pressure channel
INot used

Behavior:

  • Sends a read request to the module
  • Program waits for module response
  • Returned data is processed internally

F52 MultiPlexer

Sends command to MultiPlexer
IAction
0OFF
1ON
2Invert

How can we help?