V1.1.4

• bugfix: timeoffset can be send through SmartConfig2.0

V1.1.3

• bugfix: applied time offest did gets lost after repower

V1.1.2

• added info if switch carrier operator
• added feeback messages from cellular for default operation
• do not update time from cellular if time is off for more then a year

V1.1.1

• added roaming SIM option

V1.1.0

• added cellular infos during powerup
• Added reset function
• added ability to request settings via MQTT
• added option to delete certificates

V1.0.9

• added more debug informations for transmitter
• set timeout for choosing different provider to 3 minutes

V1.0.8

• some bug fixes

V1.0.6

• added HTTP and MQTT functions
• firmware log added

V1.0.5

• improved firmware download with debug informations

V1.0.4

• some bug fixes

V1.0.3

• send only data if variable and value has content

V1.0.2

• Enable registration to home network

V1.0.1

• Added debug informations

V1.0.0

• Updated firmware to access the transmitter directly
  • will update transmitter firmware over the air
• Enhanced firmware update server
• real time 2-way communication
• improved connectifity to server

V0.2.5

• store historic data if transmitter is in use but not online for later upload
• added user defined functions

V0.2.4

• bugfix
  • Lost calibration point on Analog1-1 High value
  • fixed analog read offset

V0.2.3

• improved user license system
  • update license for already sold systems
• automatic update to default settings for wrong configured system

V0.2.2

• added eagle dashboard support (SmartTransmit firmware 0.1.1 and upward)
• introduced user license
• added SDI-12 support

V0.2.1

• bugfix EXO singel data request and wipe command

V0.2.0

• added output 4 support

V0.1.9

• added "gravity drained" option to use all outputs for pumping

V0.1.8

• faster update of values
• fixed RS232 variable naming

V0.1.7

• added posibility to use differnt sd file save speeds for larger data files

V0.1.6

• start sampler automaticly after 10 minutes without receiving a command

V0.1.5

• reduced save speed of datalog file in order to safely store file to selected location

V0.1.4

• added SDI-12 to RS-232 Adapter support
  • valid SDI addresses from 0 to 9
• added daily reset option
  • reset the sampler every 24h after it started
• improved GPS update
• Multiplexer can now also be controlled by PWM

V0.1.3

• added Power Save mode if voltage drops below threshold
  • decreases pump time by 2
  • increases interval time by 2

V0.1.2

• can now communicate also with SmartTransmit firmwaer V0.0.8 and below
• SmartConfig Version 1.1.1 and above needed to setup connected modules

V0.1.1

• Fixed communication issue with EXO 2/RS-232
• Firmware compatible with SmartTransmit firmware 0.0.9 and above

V0.1.0 beta

• Fixed communication issue with old SmartTransmit firmware (below 0.0.9)
• Fixed communication issue with EXO 2/RS-232

V0.1.0

• minor improvements

V0.0.9

• changed warm up time from seconds into minutes
• added ability to update SmartTransmit firmware via network
  • 10 minutes timeout for updating firmware
• added power save mode
  • switch off connected devices if supply voltage drops below threshold
• added EXO support
• changed power save settings
  • will save power for each ticked option

V0.0.7

• use the warm up time also for all sensors
• read all the sensors for set time to eliminate false readings in datalog

V0.0.6

• fixed problem with Leadmed Multiprobe
  • buffer was used the wrong way, did count each time we shiffeted data into the buffer
• print now back the incoming data from Leadmed Multiprobe without buffering

V0.0.5

• added warm up time before the actual sample process
  • enables the transmitter to connect to the server
  • restart transmitter during sampling as often as it takes to establish connection
  • improved connection time

V0.0.4

• Improved analog reading accuracy
• switch on RS-485 power supply if a RS-485 device has been selected

V0.0.3 beta

• bug fix module communication

V0.0.3

• added basic debug information from transmitter
• updated the data handling for the latest Leadmed multi sensor
• bug fix
  • data download issue

V0.0.2:

• added functions
  • Up to 18 power ports can now be switched
  • increase communication speed between SmartSampler and SmartTransmit
    • transmitter must have at least firmware V0.0.1
  • LED will now also blink for debug purposes

V0.0.1:

• Minor bug fixes
  • fixed restart on high data update rates
• added functions
  • added basic information stream to transmitter
  • fine tuning of the power outputs now possible
  • updates settings over transmitter

V0.0.0:

• Initial upload.